Waste Water Treatment Chemicals

We are familiar with a variety of chemicals that allow for the treatment of waste water to reduce waste or allow for recycling.

To see some of our products, scroll down or select a category:

Coagulants

We offer a selection of these chemicals that allow total suspended solids to clump or coagulate so that they can be filtered out.

Family Products Description
EnviroBrite
WTC-815
Concentrated liquid material unique to A Brite, that produces stronger coagulation and floc action than is possible from inorganic iron and aluminum salts. It produces large, rapidly settling floc, yet reduces sludge volume. Ideal for breaking highly chelated waste streams, substantially reducing sludge and removing turbidity in the water.
EnviroBrite
WTC-104
Assist the anionic polymer in flocculation of heavy metal precipitates. WTC-104 helps produce a dense rapidly settling floc and does so with less sludge volume than inorganic seeds such as ferrous sulfate and alum.
EnviroBrite
WTC-100
A concentrated solution of divalent metals and coagulants that are effective in breaking heavy metal chelates and oil emulsions from alkaline cleaner streams that are often associated with metal finishing waste streams.

Bentonite clays and blended formulations

Our systems are primarily Bentonite clay systems that are designed to remove a range of oils, metals and suspended solids.

Family Products Description
Bentonite Clays
Introduction
WBC products are based on sodium bentonite clay. They are available pure or blended with other dry chemicals to treat a wide range of wastewater streams. Polymers and other powders are mixed with clay and are time released when added to a waste stream. A series of sequential chemical reactions take place without operator intervention, saving time and labor. The entire treatment process is simplified by minimizing treatment steps and equipment needed. WBC products will encapsulate contaminates, resulting in a sludge that is usually non-leachable and therefore non-hazardous, substantially reducing disposal cost. It removes oil and grease while reducing BOD, TSS and heavy metals. WBC products also create a strong filterable floc by allowing the floc to readily release water resulting in a drier sludge cake.
EnviroBrite
WBC-600
Powdered clay material used in combination with other chemicals.
EnviroBrite
WBC-630
A blend that reduces pH and contains an anionic polymer.
EnviroBrite
WBC-650
A blend contains an anionic polymer and raises the ph.
EnviroBrite
WBC-730
A blend that reduces pH and contains a cationic polymer
EnviroBrite
WBC-750
A blend that raises pH and contains a cationic polymer

Flocculants

These catalyst substances cause a chemical reaction with total suspended solids to encapsulate solids and allow for more complete removal.

Family Products Description
EnviroBrite
WTF-371
Full charge emulsion anionic polymer designed for maximum performance heavy metal precipitation. Diluted stock solutions are used at the rate of 8-10 ppm. Finest and most economical emulsion polymer available.
EnviroBrite
WTF-350
A medium molecular weight, anionic polymer used as a precipitation aid and sludge conditioner. It is designed to be used at full strength, eliminating the need to make up stock solutions prior to use, thus completely eliminating the make up difficulties of powders and emulsions.
EnviroBrite
WTF-431
A unique, high molecular weight, super concentrated, low-medium charge, cationic poly-acrylamide designed to be used as a precipitation aid and sludge conditioner for waste water treatment systems. This acrylic acid/acrylamide copolymer usually performs well between the 8.0-12.0 pH range.

Precipitants

We offer a full range of precipitant chemicals that are useable in most systems.

Family Products Description
EnviroBrite
DROPOUT
Highly concentrated liquid designed to precipitate heavy metals from aqueous mediums. Solutions treated with DROPOUT provide heavy metal precipitates that have much lower solubility’s and generate less sludge than their respective sodium and magnesium hydroxide precipitates. Effective over a wide pH range.
EnviroBrite
WTP-440
WTP 440 is a liquid material specifically designed to treat and remove heavy metals from waste streams. It can be used as a DTC/Carbamate substitute or replacement and in some situations may perform better. The product performs best at a pH of 8 –9 however it can also be used over a wide pH range and when used as directed, provides nearly complete precipitation of metals even in the presence of heavy chelating or sequestering agents. With regular use, it produces a sludge cake that is compact, highly insoluble and easily dewatered

Defoamers

Family Products Description
EnviroBrite
WTD-530
Highly concentrated liquid, designed to defoam waste water streams. It is highly effective in defoaming cleaners, anodizing sealers, treated plating baths, screen room and other metal finishing effluent applications. Water based defoamer does not contain any silicone, silicates or petroleum products.